Drone Parts

Ardupilot Mega APM 2.8 Flight Controller Arduino Compatible

Ardupilot Mega APM 2.8 Flight Controller Arduino Compatible

APM 2.8 ArduPilot Flight Control Board with Protective Case The APM 2.8 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition. It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints. Available with top or side connectors. Features of APM 2.8 ArduPilot Flight Control Board: Arduino Compatible!. Can be ordered with top entry pins for attaching connectors vertically, or as side entry pins to slide your connectors in to either end horizontally. Includes 3-axis gyro, accelerometer and magnetometer, along with a high-performance barometer. Onboard 4 MegaByte Dataflash chip for automatic datalogging. Optional off-board GPS, uBlox LEA-6H module with Compass. One of the first open source autopilot systems to use Invensense's 6 DoF Accelerometer/Gyro MPU-6000. Barometric pressure...
Rs2,900.00
Add:
Brushless DC Motors 1000Kv for Quadcopter/Multirotor/Drone

Brushless DC Motors 1000Kv for Quadcopter/Multirotor/Drone

1000Kv Brushless DC Motors for Quadcopter 1000Kv Brushless Quadcopter Motors is a Brushless DC electric motor (BLDC motors) also known as electronically commutated motors (ECMs, EC motors) are synchronous motors that are powered by a DC electric source via an integrated inverter switching power supply, which produces an AC electric signal to drive the motor. In this context, AC, alternating current, does not imply a sinusoidal waveform, but rather a bi-directional current with no restriction on waveform. WORKING PRINCIPLE:- A brushless dc motors for quadcopter is constructed with a permanent magnet rotor and wire wound stator poles.Electrical energy is converted to mechanical energy by the magnetic attractive forces between the permanent magnet rotor and a rotating magnetic field induced in the wound stator poles. there are three electromagnetic circuits connected at a common point. Each electromagnetic circuit is split in the center, thereby permitting the permanent magnet rotor to...
Rs550.00
Add:
Brushless Motor Speed Controller ESC 30A

Brushless Motor Speed Controller ESC 30A

30AMP BLDC ESC Circuit This is fully programmable 30A BLDC ESC Circuit with 5V, 3A BEC. Can drive motors with continuous 30Amp load current. It has sturdy construction with 2 separate PCBs for Controller and Electronic Speed Controller power MOSFETs. It can be powered with 2-4 lithium Polymer batteries or 5-12 NiMH / NiCd batteries. It has separate voltage regulator for the microcontroller for providing good anti-jamming capability. It is most suitable for UAVs, Aircrafts and Helicopters. Specification of 30AMP BLDC ESC Circuit : Output: 20A continuous; 25Amps for 10 seconds Input: 30A continuous; 35Amps for 10 seconds Input voltage: 2-4 cells Lithium Polymer / Lithium Ion battery or 5-12 cells NiMH / NiCd BEC: 5V, 2Amp for external receiver and servos Max Speed: 2 Pole: 210,000rpm; 6 Pole: 70,000rpm; 12 Pole: 35,000rpm Weight: 22gms Size: 47mm x 27mm x 12mm Features of 30AMP BLDC ESC Circuit : High quality MOSFETs for BLDC motor drive High performance microcontroller for best...
Rs450.00
Add:
Min:  100
Brushless Motor Speed Controller ESC 30A with Simonk Firmware

Brushless Motor Speed Controller ESC 30A with Simonk Firmware

Brushless Electronics Speed Controller with SimonK firmware flashed for high speed control of brushless motors. This is recommended ESC for using with multirotor aircrafts like quadcopter, hexcopter and octocopter. Can be used with 3 or 4 Cell Li-Po. Programmable for throttle range.. Specifications: Input voltage:DC 6-16.8V(2-4S Lixx) BEC:5V 2amp Running current:30A(Output: Continuous 30A, Burst 40A up to 10 Secs.) Size: 36mm (L) * 26mm (W) * 7mm (H). Weight: 32g
Rs600.00
Add:
DJI 2212 920KV Brushless Motor For Quadcopter/Multirotor/Drone

DJI 2212 920KV Brushless Motor For Quadcopter/Multirotor/Drone

DJI 2212 920KV Brushless Motor for Quadcopter/Multirotor/Drone 920Kv Brushless DC Motor is a Brushless DC electric motor (BLDC motors, BL motors) also known as electronically commutated motors (ECMs, EC motors) are synchronous motors that are powered by a DC electric source via an integrated inverter switching power supply, which produces an AC electric signal to drive the motor. Features of DJI 2212 920KV Brushless Motor: KV(rpm/v): 920. Max Power: 370W. Max Thrust: 1200 grams. Weight: 53 grams. Shaft Diameter: 4mm. Shaft Length: 49mm Recommended Propeller for battery: 12x4.5 for 2S battery; 10x4.5 for 4S battery. Battery: 2S-3S Li-Po. ESC (A): FMT 30A (recommended). Applications of DJI 2212 920KV Brushless Motor: Used in light weight quadcopters.
Rs950.00
Add:
KK2.15 LCD Flight Control Board

KK2.15 LCD Flight Control Board

KK2.15 LCD Flight Control Board 6050MPU 644PA Multirotor update version for KK2 kk2.1 The KK2.1.5 is next big evolution of the first generation KK flight control boards. The KK2.1.5 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts. The LCD screen and built in software makes install and setup easier than ever. A host of multi-rotor craft types are pr-installed, simply select your craft type, check motor layout/propeller direction, calibrate your ESCs and radio and you’re ready to go! All of which is done with easy to follow on screen prompts. Features of KK2.15 LCD Flight Control Board 6050MPU 644PA Multi-rotor: Size: 50.5mm x 50.5mm x 12mm. Weight: 21 gram (Inc Piezo buzzer). IC: Atmega644 PA. Gyro/Acc: 6050MPU InvenSense Inc. Auto-level: Yes. Input Voltage: 4.8-6.0V. AVR interface: standard 6 pin. Signal from Receiver: 1520us (5 channels). Signal to ESC: 1520us. Firmware Version: 1.9S. Pr-installed firmware. Applications of KK2.15 LCD...
Rs1,450.00
Add:
Pixhawk PX4 2.4.8 32bit Flight Controller with accessories

Pixhawk PX4 2.4.8 32bit Flight Controller with accessories

The benefits of the Pixhawk system include integrated multithreading, a Unix/Linux-like programming environment, completely new autopilot functions such as sophisticated scripting of missions and flight behavior, and a custom PX4 driver layer ensuring tight timing across all processes. These advanced capabilities ensure that there are no limitations to your autonomous vehicle. Pixhawk allows existing APM and PX4 operators to seamlessly transition to this system and lowers the barriers to entry for new users to participate in the exciting world of autonomous vehicles. The flagship Pixhawk module will be accompanied by new peripheral options, including a digital airspeed sensor, support for an external multi-color LED indicator and an external magnetometer. All peripherals are automatically detected and configured. This package includes all essential parts required to make your multirotor, plane or rover working and controllable through autopilot. Other accessories like telemetry,...
Rs9,900.00
Add:
Quadcopter Legs Pair

Quadcopter Legs Pair

Quadcopter Legs Pair The quadcopter frame legs pair is a high quality Plastic frame legs that offers both great looks and performance. Built from light weight yet extremely rigid synthetic material, it is the best combination of weight savings and strength in the price it comes in. Features of Quadcopter Legs Pair: Easy to Use. Weight: 240g. Width: 498mm. Motor Bolt Holes: 22~32mm. Long life. Applications of Quadcopter Legs Pair: These are used in quad-copter.
Rs249.00
Add:
R450 Quadcopter Frame with Integrated PCB

R450 Quadcopter Frame with Integrated PCB

R450 Quadcopter Frame with Integrated PCB The R450 is a well thought out 450mm quad frame built from quality materials. The main frame is glass fiber while the arms are constructed from ultra durable polyamide nylon. The R450 features integrated PCB connections for direct soldering of your ESCs. This eliminates the need for a power distribution board or messy multi-connectors keeping your electronics layout very tidy. Specifications of R450 Quadcopter Frame with Integrated PCB: Width: 450mm. Height: 55mm. Weight: 270g (w/out electronics). Motor Mount Bolt Holes: 16/19mm. Features of R450 Quadcopter Frame with Integrated PCB: Built from quality glass fiber and polyamide nylon. Integrated PCB connections for direct soldering of your ESCs Pre-threaded brass sleeves for all of the frame bolts. Colored arms for orientation to keep you flying in the right direction. Large mounting tabs on main frame bottom plate for easy camera mounting. Easy assembly. Applications of R450 Quadcopter Frame...
Rs900.00
Add:
R550 Hexacopter Frame with Integrated PCB For Easy Wiring

R550 Hexacopter Frame with Integrated PCB For Easy Wiring

R550 Hexacopter Frame with Integrated PCB For Easy Wiring The R550 Hexacopter Frame is a 550mm hexacopter frame built from quality materials. The main frame is glass fiber while the arms are constructed from ultra durable polyamide nylon. Features of R550 Hexacopter Frame with Integrated PCB For Easy Wiring: Width: 550mm Height: 55mm Weight: 435g Motor Mount Bolt Holes: 16/19mm Applications of R550 Hexacopter Frame with Integrated PCB For Easy Wiring: DIY Quadcopter projects. Quadrotor (quadcopter). Electrical/Electronic projects quadcopter.
Rs1,199.00
Add:
Your IP Address is: 54.224.13.210
Copyright © 2017 Robotscraft. Powered by Zen Cart