Sensors

37 in 1 Arduino Sensor Kit

37 in 1 Arduino Sensor Kit

ARDUNIO 37 IN 1 SENSOR KT 37 in 1 sensor kit for all applications. Providing various simple to complex sensor interface for embedded teaching. The Kit Contains Following Items :   1)Temperature sensor module 2) Vibration switch module 3) Hall magnetic sensor module 4) Key switch module 5) Infrared emission sensor module 6) Laser sensor module 7) Small passive buzzer module 8) 3-color full-color LED SMD modules 9) Photo interrupter module 10) 2-color LED module 11) Active buzzer module 12) Temperature sensor module 13) Temperature and humidity sensor module 14) 3-color LED module 1)Temperature sensor module 2) Vibration switch module 3) Hall magnetic sensor module 4) Key switch module 5) Infrared emission sensor module 6) Laser sensor module 7) Small passive buzzer module 8) 3-color full-color LED SMD modules 9) Photo interrupter module 10) 2-color LED module 11) Active buzzer module 12) Temperature sensor module 13)...
Rs2,500.00
Add:
BAROMETRIC PRESSURE SENSOR BREAKOUT - BMP180

BAROMETRIC PRESSURE SENSOR BREAKOUT - BMP180

BAROMETRIC PRESSURE SENSOR BREAKOUT - BMP180 This is a breakout board for the Bosch BMP180 high-precision, low-power digital barometer. The BMP180 offers a pressure measuring range of 300 to 1100 hPa with an accuracy down to 0.02 hPa in advanced resolution mode. It’s based on piezo-resistive technology for high accuracy, ruggedness and long term stability. These come factory-calibrated, with the calibration coefficients already stored in ROM This breadboard-friendly board breaks out every pin to a 5-pin 0.1" pitch header. VCC can be from 1.8V to 3.6V and is I/O lines are 5V tolerant. The analog and digital supplies (VDDD and VDDA) are tied to a single header pin, but are separately decoupled. It connects to a microcontroller via I²C bus (also known as TWI, or on the Arduino, the “Wire” library) Features of BAROMETRIC PRESSURE SENSOR BREAKOUT - BMP180 :   Digital two wire (I²C, TWI, “Wire”) interface Wide barometric pressure range Flexible supply voltage...
Rs370.00
Add:
BH1750 Light Intensity Module

BH1750 Light Intensity Module

BH1750 LIGHT INTENSITY MODULE This is a BH1750 light intensity sensor breakout board with a 16 bit AD converter built-in which can directly output a digital signal, there is no need for complicated calculations. This is a more acurate and easier to use version of the simple foto resistor which only outputs a voltage that needs to be calculated in order to obtain meaningful data. With the BH1750 Light Sensor intensity can be directly measured by the luxmeter, without needing to make calculations. The data which is output by this sensor is directly output in Lux (Lx). When objects which are lighted in homogeneous get the 1 lx luminous flux in one square meter ,their light intensity is 1lx Features:- :   Interface: I2C Power supply :3-5v Data range 0-65535 Sensor built 16bitAD converter Small measurement variation (+/- 20%) Dimensions: 13.9mm X 18.5mm
Rs240.00
Add:
CURRENT SENSOR MODULE 5A ACS712

CURRENT SENSOR MODULE 5A ACS712

CURRENT SENSOR MODULE 5A ACS712 Accurate sensor to measure AC/DC current up to 5A. The sensor can even measure high AC mains current and is still isolated from the measuring part due to integrated hall sensor. The board operates on 5V. ACS712 current sensor operates from 5V and outputs analog voltage proportional to current measured on the sensing terminals. One can simple use a microcontroller ADC to read the values. Sensing terminal can even measure current for loads operating at high voltages like 230V AC mains while output sensed voltage is isolated from measuring part. Provides up to 3000 VRMS galvanic isolation. The low-profile, small form factor packages are ideal for reducing PCB area over sense resistor op-amp or bulky current transformer configurations. The low resistance internal conductor allows for sensing up to 5A continuous current. Providing typical output error of 1%. Features of CURRENT SENSOR MODULE 5A ACS712 :   185 mV/A output sensitivity 5.0 V,...
Rs295.00
Add:
DHT22 DIGITAL TEMPERATURE AND HUMIDITY SENSOR MODULE WITH CABLE

DHT22 DIGITAL TEMPERATURE AND HUMIDITY SENSOR MODULE WITH CABLE

DHT22 DIGITAL TEMPERATURE AND HUMIDITY SENSOR MODULE WITH CABLE DHT22 capacitive humidity sensing digital temperature and humidity module is one that contains the compound has been calibrated digital signal output of the temperature and humidity sensors. Application of a dedicated digital modules collection technology and the temperature and humidity sensing technology, to ensure that the product has high reliability and excellent long-term stability. The sensor includes a capacitive sensor wet components and a high-precision temperature measurement devices, and connected with a high-performance 8-bit microcontroller. The product has excellent quality, fast response, strong anti-jamming capability, and high cost. Standard single-bus interface, system integration quick and easy. Small size, low power consumption, signal transmission distance up to 20 meters, making it the best choice of all kinds of applications and even the most demanding applications. DHT22 has higher precision and...
Rs490.00
Add:
Flame Sensor Module

Flame Sensor Module

Flame Sensor Module Flame Detection Sensor Module is sensitive to the flame, but also can detect ordinary light. Usually used as a flame alarm. Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm. Detection point of about 60 degrees, particularly sensitive to the flame spectrum. Sensitivity is adjustable, stable performance. Features of Flame Sensor Module :   Detection angle about 60 degrees, it is sensitive to the flame spectrum. Accuracy adjustable. Operating voltage 3.3V-5V Output a. analog voltage outputb. digital switch outputs (0 and 1) With a mounting screw holePCB size: 3cm * 1.6cm Power indicator (red) and digital switch output indicator (green) Comparator chip LM393 ,it is stable. Flame detection distance, lighter flame test can be triggered within 0.8m, if the intensity of flame is high , the detection distance will be increased.
Rs110.00
Add:
Gas Sensor For Arduino

Gas Sensor For Arduino

Gas Sensor Kit for Arduino And Raspberry Pi The Package Includes Following Products :   MQ-135 Air Quality & Hazardous Gas Sensor Module MQ-2 Smoke Methane Gas & Liquefied Flammable Gas Sensor Module MQ-3 Alcohol Ethanol Gas Sensor Module MQ-4 Methane Gas Sensor Module MQ-5 Liquefied Gas & Coal Gas Sensor Module MQ-6 Isobutene Propane Gas Sensor Module MQ-7 Carbon Monoxide Gas Sensor Module MQ-8 Hydrogen H2 Gas Sensor Module MQ-9 Carbon Monoxide Combustible Gas Sensor Module)
Rs1,500.00
Add:
Heart Beat Sensor for Arduino And Raspberry Pi

Heart Beat Sensor for Arduino And Raspberry Pi

HEART BEAT SENSOR For Arduino And Raspberry Pi This module uses bright infrared (IR) LED and a phototransistor to detect the pulse of the finger, a red LED flashes with each pulse. Pulse monitor works as follows: The LED is the light side of the finger, and phototransistor on the other side of the finger, phototransistor used to obtain the flux emitted, when the blood pressure pulse by the finger when the resistance of the phototransistor will be slight changed. We choose a very high resistance resistor R1, because most of the light through the finger is absorbed, it is desirable phototransistor sensitive enough. Resistance can be selected by experiment to get the best results. The most important is to keep the shield stray light into the phototransistor. For home lighting that is particularly important because the lights at home mostly based 50HZ or 60HZ fluctuate, so faint heartbeat will add considerable noise.
Rs199.00
Add:
L3G4200D 3AXIS GYRO

L3G4200D 3AXIS GYRO

L3G4200D 3AXIS GYRO Raw angular rate and temperature data measurements are accessed from the selectable digital I2C or SPI interface. The small package design and SIP interface accompanied by the mounting hole make the sensor easy to integrate into your projects. Designed to be used with a variety of microcontrollers, the module has a large operating voltage window. Features of  :   3-axis angular rate sensor (yaw, pitch & roll) make it great for model aircraft navigation systems. Supports both I2C and SPI for whichever method of communication you desire. Three selectable scales: 250/500/2000 degrees/sec (dps) Embedded power down and sleep mode to minimize current draw 16 bit-rate value data output 8-bit temperature data output
Rs595.00
Add:
LASER RANGING SENSOR TOF BASED ON VL53L0X

LASER RANGING SENSOR TOF BASED ON VL53L0X

LASER RANGING SENSOR TOF BASED ON VL53L0X This sensor is a carrier/breakout board for ST’s VL53L0X laser-ranging sensor, which measures the range to a target object up to 2 m away. The VL53L0X uses time-of-flight measurements of infrared pulses for ranging, allowing it to give accurate results independent of the target’s color and surface. Distance measurements can be read through a digital I²C interface. The board has a 2.8 V linear regulator and integrated level-shifters that allow it to work over an input voltage range of 2.6 V to 5.5 V, and the 0.1″ pin spacing makes it easy to use with standard solderless breadboards and 0.1″ perfboards Specifications of VL53L0X Time-of-Flight Distance Sensor break out board :   Resolution: 1 mm/font> Maximum range: 2m Interface: I²C Minimum operating voltage: 2.6 V Maximum operating voltage: 5.5 V Supply current: 10 mA Dimension: 0.5" × 0.7" × 0.085" (13 mm × 18 mm × 2 mm)
Rs1,170.00
Add:
Your IP Address is: 54.224.13.210
Copyright © 2017 Robotscraft. Powered by Zen Cart