All Products

BAROMETRIC PRESSURE SENSOR BREAKOUT - BMP180

In Stock: 100

Add:

Model: RCS-SENSORS-505
Price: Rs370.00

Weight: 200grams

BAROMETRIC PRESSURE SENSOR BREAKOUT - BMP180 This is a breakout board for the Bosch BMP180 high-precision, low-power digital barometer. The BMP180 offers a pressure measuring range of 300 to 1100 hPa with an accuracy down to 0.02 hPa in advanced resolution mode. It’s based on piezo-resistive technology for high accuracy, ruggedness and long term stability. These come factory-calibrated, with the calibration coefficients already stored in ROM This breadboard-friendly board breaks out every pin to a 5-pin 0.1" pitch header. VCC can be from 1.8V to 3.6V and is I/O lines are 5V tolerant. The analog and digital supplies (VDDD and VDDA) are tied to a single header pin, but are separately decoupled. It connects to a microcontroller via I²C bus (also known as TWI, or on the Arduino, the “Wire” library) Features of BAROMETRIC PRESSURE SENSOR BREAKOUT - BMP180 :   Digital two wire (I²C, TWI, “Wire”) interface Wide barometric pressure range Flexible supply voltage ... more info
BH1750 Light Intensity Module

In Stock: 100

Add:

Model: RCS-SENSORS-501
Price: Rs240.00

Weight: 0grams

BH1750 LIGHT INTENSITY MODULE This is a BH1750 light intensity sensor breakout board with a 16 bit AD converter built-in which can directly output a digital signal, there is no need for complicated calculations. This is a more acurate and easier to use version of the simple foto resistor which only outputs a voltage that needs to be calculated in order to obtain meaningful data. With the BH1750 Light Sensor intensity can be directly measured by the luxmeter, without needing to make calculations. The data which is output by this sensor is directly output in Lux (Lx). When objects which are lighted in homogeneous get the 1 lx luminous flux in one square meter ,their light intensity is 1lx Features:- :   Interface: I2C Power supply :3-5v Data range 0-65535 Sensor built 16bitAD converter Small measurement variation (+/- 20%) Dimensions: 13.9mm X 18.5mm
Bluetooth Transceiver Module with TTL Outputs-HC05

In Stock: 100

Add:
Max: 1

Model: ROBO-hc05
Price: Rs330.00

Weight: 300grams

Product description The bluetooth transceiver module is used as UART RS232 serial converter module. It can easily transfer the UART data through the wireless bluetooth, without complex pieceB layout or deep knowledge in the bluetooth software stack, you can also connect this bluetooth module with your devices listed below, MCU, ARM or DSP systems, GPS or GSM, Sensor Modules, SOC systems. Personal Digital Assistants (PDAs), computer accessories. Brand Name Robotscraft Colour Green Ean 0702535831363 Included Components HC05 Bluetooth Module Item Height 0.75  centimeters Item Length 4.5  centimeters Item Weight 9 grams Item Width 0.51  centimeters Manufacturer Series Number arb004 Material Composition Silicone Number of Items 1 Part Number arb004 Specification Met Bluetooth protocol- v2.0+EDR Frequency Range- 2.4GHz Modulation- GFSK
BO-GEARED MOTOR

In Stock: 100

Add:

Model: DC-BO-Gear-Motor
Price: Rs85.00

Weight: 300grams

• 60RPM with Gearbox • 3-12V DC Motors • Used for making small and medium robots • Low cost gear motor (Original product may slightly vary from the image given) Item Weight 41 g Product Dimensions 7 x 5.6 x 4.2 cm Item part number XTBO6 Operating System Windows Batteries Included No
Brushless DC Motors 1000Kv for Quadcopter/Multirotor/Drone

In Stock: 10

Add:

Model: RCS-DR-1501
Price: Rs550.00

Weight: 150grams

1000Kv Brushless DC Motors for Quadcopter 1000Kv Brushless Quadcopter Motors is a Brushless DC electric motor (BLDC motors) also known as electronically commutated motors (ECMs, EC motors) are synchronous motors that are powered by a DC electric source via an integrated inverter switching power supply, which produces an AC electric signal to drive the motor. In this context, AC, alternating current, does not imply a sinusoidal waveform, but rather a bi-directional current with no restriction on waveform. WORKING PRINCIPLE:- A brushless dc motors for quadcopter is constructed with a permanent magnet rotor and wire wound stator poles.Electrical energy is converted to mechanical energy by the magnetic attractive forces between the permanent magnet rotor and a rotating magnetic field induced in the wound stator poles. there are three electromagnetic circuits connected at a common point. Each electromagnetic circuit is split in the center, thereby permitting the permanent magnet rotor to ... more info
Brushless Motor Speed Controller ESC 30A

In Stock: 100

Add:
Min:  100

Model: RCS-DR-1451
Price: Rs450.00

Weight: 100grams

30AMP BLDC ESC Circuit This is fully programmable 30A BLDC ESC Circuit with 5V, 3A BEC. Can drive motors with continuous 30Amp load current. It has sturdy construction with 2 separate PCBs for Controller and Electronic Speed Controller power MOSFETs. It can be powered with 2-4 lithium Polymer batteries or 5-12 NiMH / NiCd batteries. It has separate voltage regulator for the microcontroller for providing good anti-jamming capability. It is most suitable for UAVs, Aircrafts and Helicopters. Specification of 30AMP BLDC ESC Circuit : Output: 20A continuous; 25Amps for 10 seconds Input: 30A continuous; 35Amps for 10 seconds Input voltage: 2-4 cells Lithium Polymer / Lithium Ion battery or 5-12 cells NiMH / NiCd BEC: 5V, 2Amp for external receiver and servos Max Speed: 2 Pole: 210,000rpm; 6 Pole: 70,000rpm; 12 Pole: 35,000rpm Weight: 22gms Size: 47mm x 27mm x 12mm Features of 30AMP BLDC ESC Circuit : High quality MOSFETs for BLDC motor drive High performance microcontroller for best ... more info
Brushless Motor Speed Controller ESC 30A with Simonk Firmware

In Stock: 100

Add:

Model: RCS-DR-1452
Price: Rs600.00

Weight: 100grams

Brushless Electronics Speed Controller with SimonK firmware flashed for high speed control of brushless motors. This is recommended ESC for using with multirotor aircrafts like quadcopter, hexcopter and octocopter. Can be used with 3 or 4 Cell Li-Po. Programmable for throttle range.. Specifications: Input voltage:DC 6-16.8V(2-4S Lixx) BEC:5V 2amp Running current:30A(Output: Continuous 30A, Burst 40A up to 10 Secs.) Size: 36mm (L) * 26mm (W) * 7mm (H). Weight: 32g
CURRENT SENSOR MODULE 5A ACS712

In Stock: 200

Add:

Model: RCS-SENSORS-507
Price: Rs295.00

Weight: 200grams

CURRENT SENSOR MODULE 5A ACS712 Accurate sensor to measure AC/DC current up to 5A. The sensor can even measure high AC mains current and is still isolated from the measuring part due to integrated hall sensor. The board operates on 5V. ACS712 current sensor operates from 5V and outputs analog voltage proportional to current measured on the sensing terminals. One can simple use a microcontroller ADC to read the values. Sensing terminal can even measure current for loads operating at high voltages like 230V AC mains while output sensed voltage is isolated from measuring part. Provides up to 3000 VRMS galvanic isolation. The low-profile, small form factor packages are ideal for reducing PCB area over sense resistor op-amp or bulky current transformer configurations. The low resistance internal conductor allows for sensing up to 5A continuous current. Providing typical output error of 1%. Features of CURRENT SENSOR MODULE 5A ACS712 :   185 mV/A output sensitivity 5.0 V, ... more info
DC Gear Motor 12V 10 RPM For Arduino/Raspberry-Pi/Robotics

In Stock: 10

Add:

Model: RCS-DM-1005
Price: Rs160.00

Weight: 150grams

10 RPM Center Shaft Metal Gear DC Motor for Arduino/Raspberry-Pi/Robotics A DC Geared DC motor is a simple DC motor with gear box attached to the shaft of the motor which is mechanically commutated electric motor powered from direct current (DC). Features of 10 RPM Center Shaft Metal Gear DC Motor for Arduino/Raspberry-Pi/Robotics Gear materials: metal. Magnet types: permanent-magnet. Brush-type: Brush. Motor Type: Homopolar motors. Magnet type: Ferrite magnets. Torque multiplication: Generate a large force at a low speed. Applications of 10 RPM Center Shaft Metal Gear DC Motor for Arduino/Raspberry-Pi/Robotics DIY Projects. Battery-operated toys. Disk drives . Machines Medical equipment. Radio-controlled aircraft. Automobiles Drive systems Positioning. Industrial and consumer actuators Winches Robotics Mixers. Robotic projects.
DC Gear Motor 12V 100 RPM For Arduino/Raspberry-Pi/Robotics

In Stock: 10

Add:

Model: RCS-DM-1008
Price: Rs140.00

Weight: 150grams

100 RPM Center Shaft Metal Gear DC Motor for Arduino/Raspberry-Pi/Robotics A DC Geared DC motor is a simple DC motor with gear box attached to the shaft of the motor which is mechanically commutated electric motor powered from direct current (DC). Features of 100 RPM Center Shaft Metal Gear DC Motor for Arduino/Raspberry-Pi/Robotics Gear materials: Metal. Motor types: Permanent-magnet. Brush-type: Brush. Drive Type: Homopolar motors. Magnet types: Ferrite magnets. Torque multiplication: Generate a large force at a low speed. Applications of 100 RPM Center Shaft Metal Gear DC Motor for Arduino/Raspberry-Pi/Robotics DIY Projects. Battery-operated toys. Disk drives Steel rolling mills Paper. Machines Medical equipment. Radio-controlled aircraft. Automobiles Drive systems Positioning. Industrial and consumer actuators Winches Robotics Mixers. Robotic projects.
Your IP Address is: 54.166.150.10
Copyright © 2017 Robotscraft. Powered by Zen Cart